I N S T A L L A T I O N I N S T R U C T I O N S
Single Ceiling Mount
MCS6000 Series
Installation Instructions
MCS6000 Series
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
3
MCS6000 Series
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
5/32"
(Provided)
PARTS
A (1)
B (1)
5/32"
4
Installation Instructions
MCS6000 Series
INSTALLATION
WARNING: FAILURE TO PROVIDE ADEQUATE
STRUCTURAL STRENGTH FOR THIS COMPONENT CAN
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE
TO EQUIPMENT! It is the installer’s responsibility to make
sure the structure to which this component is attached can
support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
1
(A)
Attaching MCS to NPT Pipe
CAUTION: Watch for pinch points. Do not place fingers
between moveable parts.
Display
1. Thread the MCS (A) onto the existing 1-1/2" NPT pipe until
tight. (See Figure 1)
Figure 2
2. Using the hex head wrench (B) tighten the set screw into the
MCS threaded collar to prevent movement of the mount.
(See Figure 1)
WARNING: DISPLAY MAY WEIGH IN EXCESS OF 40
LBS! Always use two people and proper lifting techniques
when installing or positioning display on MCS.
NPT
Pipe
2. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes. (See Fig. 2, 3 and 4)
Set
Screw
2
(A)
(A)
Interface Bracket
(will vary in
appearance)
of Display
Back
Figure 1
Attaching Interface Bracket to Display
Figure 3
1. Attach interface bracket to display following instructions
included with interface bracket kit.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting
buttons are completely engaged in mounting holes.
Attaching Displays to MCS
1. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in MCS. (See Figures 2, 3 and 4)
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 4).
5
MCS6000 Series
Installation Instructions
Remove bolt
or padlock
if used
1
2
May remove
pin and nut and
move to lower holes
4
Pin in
"Closed"
position -
move to
"Open"
5
position to
remove
display
A padlock or bolt
may be placed
through latch holes
4
Figure 4
Removing Display from MCS
1. Disconnect all power/audio/video cables.
2. Remove bolt or padlock from faceplate (if used).
(See Figure 5)
NOTE: The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
Pin in
"Open"
position -
move to
"Closed"
position
3. Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 5)
after display
is removed.
WARNING: THE DISPLAY MAY WEIGH IN EXCESS OF
40 LBS EACH! Always use two people and proper lifting
techniques when installing or positioning display on MCS.
Figure 5
4. Carefully lift display from MCS.
5. Lift up on pin and place flag back against faceplate to return
it to "Closed" position. (See Figure 5)
Adjusting Display
CAUTION: Watch for pinch points. Do not place fingers
between moveable parts.
Adjusting Roll
1. Using a 9/16" wrench, loosen the Nylock roll adjustment nut
on back of mounting plate. (See Figure 6)
2. Tilt the faceplate left or right as required.
3. TIghten nut.
NOTE: Do NOT overtighten fasteners.
Adjusting Pitch
1. Adjust display to the desired pitch.
2. Using the 5/32" hex head wrench (B), tighten the pitch
adjustment screw to hold mount in position. (See Figure 6)
6
Installation Instructions
MCS6000 Series
Roll
Adjustment
Nut
Pitch
Adjustment
Screw
Figure 6
7
MCS6000 Series
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
8805-000144 Rev. E
©2007 Chief Manufacturing
10/07
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220
+86-755-8996 9217
|